Brute Force Fab

Brute Force FabBrute Force FabBrute Force Fab

Brute Force Fab

Brute Force FabBrute Force FabBrute Force Fab
  • Home
  • Front Bumpers
    • 05-11 Tacoma front bumper
    • 12-15 Tacoma front bumper
    • 16+ Tacoma Plate Bumpers
    • 16+ Tacoma Hybrid Front
    • 5th Gen 4Runner
    • 1st Gen Tundra Fronts
    • 1st Gen Sequoia Fronts
  • Rear Bumpers
    • 05-15 Tacoma Rears
    • 16+ Tacoma Rears
    • 5th Gen 4Runner Rears
    • 1st Gen Tundra Rears
    • 1st Gen Sequoia Rears
  • Rock Sliders
  • Accesories
  • More
    • Home
    • Front Bumpers
      • 05-11 Tacoma front bumper
      • 12-15 Tacoma front bumper
      • 16+ Tacoma Plate Bumpers
      • 16+ Tacoma Hybrid Front
      • 5th Gen 4Runner
      • 1st Gen Tundra Fronts
      • 1st Gen Sequoia Fronts
    • Rear Bumpers
      • 05-15 Tacoma Rears
      • 16+ Tacoma Rears
      • 5th Gen 4Runner Rears
      • 1st Gen Tundra Rears
      • 1st Gen Sequoia Rears
    • Rock Sliders
    • Accesories
  • Home
  • Front Bumpers
    • 05-11 Tacoma front bumper
    • 12-15 Tacoma front bumper
    • 16+ Tacoma Plate Bumpers
    • 16+ Tacoma Hybrid Front
    • 5th Gen 4Runner
    • 1st Gen Tundra Fronts
    • 1st Gen Sequoia Fronts
  • Rear Bumpers
    • 05-15 Tacoma Rears
    • 16+ Tacoma Rears
    • 5th Gen 4Runner Rears
    • 1st Gen Tundra Rears
    • 1st Gen Sequoia Rears
  • Rock Sliders
  • Accesories

1st gen sequoia

    1st gen sequoia rears

    Sequoia Rear base Standard Features

     

    • Main Bumper CNC cut and formed from 3/16 HRPO Steel Plate 
    • 1/4'' Frame Plate Brackets
    • Built in Receiver Hitch (Not Rated but will handle anything that the factory hitch will) 
    • Cutout for the factory 7pin tow plug next to the hitch
    • Fully Mig Welded
    • 1/2 thick recovery points for a 3/4 shackle w/ a 7/8 pin
    • Comes with  Light Cutouts  that fit Baja Design S2 Flush Mounts, Diode Dynamic flush mounts, or the cheaper Amazon lights. Please specify when ordering which cutouts you prefer.
    • Comes with all necessary hardware
    • Comes with the side protection tubes
    •  Base Bumper weighs around 140lbs. and 240lbs with swingouts
    • Notes: Unfortunately aftermarket ladders will not work with our bumpers as the swingouts are to close to the back hatch when they're closed which is why we built the ladder style dual swingout and the short single swingout 
    • Comes raw steel and ready for the finish of your choice


    Pricing & Options

    • Rear Base bumper w/ standard features $1095.00

            Add On's

    • Add Single swingout tire carrier. Comes with tire mount located on the passenger side and the universal mounting plate on the drivers side (on one swingout) for mounting accessories  such as the gas can holders, propane tank mounts, hi lift, etc.. Comes with the  Brute Force HD Latch, Timken Taper roller bearings, seal, Aluminum cap  and all necessary hardware. Swingout pivots off the passenger side of the rear bumpers and cannot be changed and locks open at 90 degrees.$ 645.00


    • Add Single swingout tire carrier ( for tire only) Comes with tire mount located on the passenger side. Comes with the Brute Force HD Latch , Timken Taper roller bearings, seal, Aluminum cap  and all necessary hardware. Swingout pivots off the passenger side of the rear bumpers and cannot be changed and locks open at 90 degrees.$ 565.00


    • Add Dual Swingout tire carrier. Comes with tire mount located on the passenger side and the universal mounting plate on the drivers side (on two separate short swingouts) for mounting accessories  such as the gas can holders, propane tank mounts, hi lift, etc.. Comes with the Brute Force HD  latches , Timken Taper roller bearings, seals, Aluminum caps  and all necessary hardware.  Swingouts pivots off the driver and passenger side of the rear bumper and locks open at 90 degrees.$1175.00


    • Add Fold down aluminum camp table ( only available for the dual swingout on the drivers side) $150.00
    • Add Dual Gas Can Holder $135.00
    • Add Single Gas Can Holder $95.00
    • Propane tank mount $125.00
    • Camera relocation bracket $25.00

            Installation 

    • Installation  (no swingout) $285   single swingout  $335   Dual swingouts $395
    • NOTE: Installation includes the removal of the factory bumper, cutting the factory bumper  and installing our bumper. we can install lights (supplied by customer) into the bumper at an additional cost but we don't do any wiring or electrical work. If you have an aftermarket bumper it would need to be removed before you come for the install or we can remove it at an additional cost.

          Powder Coating

    • Only available for local pickup or installation. We Don't Ship Anything Powder Coated.
    • Rear (no swingouts) $255 single swingout $355 Dual swingouts $385
    • Single Gas can holder $25 Dual Can Holder $35
    • propane tank mount $25


    Shipping


    Shipping costs vary by location and carrier. Shipping has to be to a commercial address  with either a loading dock or forklift. We can also ship to a freight terminal which you would have to pick up from once it arrives to the terminal that's close to you.  Please use the contact form to ask us for a shipping quote. Please include your commercial address with a name of the business or a zip code so I can locate the closest freight terminal that's close to you. 

    Lead Times

    10-12 weeks

    Order Process 50% deposit , Balance plus Shipping when complete

    Local pick up is available as well


     To place an order please call or text me at (559)900-6564 . Once I have all the information I will email you an invoice that will have a link to pay with a credit card or bank card.    Make sure to list the options that you want, A zip code so that I can get a shipping quote, year and model of your vehicle 

    Brute Force Fab

    Clovis, California, United States

    5599006564

    Copyright © 2024 Brute Force Fab - All Rights Reserved.

    Powered by GoDaddy

    This website uses cookies.

    We use cookies to analyze website traffic and optimize your website experience. By accepting our use of cookies, your data will be aggregated with all other user data.

    Accept