Brute Force Fab

Brute Force FabBrute Force FabBrute Force Fab

Brute Force Fab

Brute Force FabBrute Force FabBrute Force Fab
  • Home
  • Front Bumpers
    • 05-11 Tacoma front bumper
    • 12-15 Tacoma front bumper
    • 16+ Tacoma Plate Bumpers
    • 16+ Tacoma Hybrid Front
    • 5th Gen 4Runner
    • 1st Gen Tundra Fronts
    • 1st Gen Sequoia Fronts
  • Rear Bumpers
    • 05-15 Tacoma Rears
    • 16+ Tacoma Rears
    • 5th Gen 4Runner Rears
    • 1st Gen Tundra Rears
    • 1st Gen Sequoia Rears
  • Rock Sliders
  • Accesories
  • More
    • Home
    • Front Bumpers
      • 05-11 Tacoma front bumper
      • 12-15 Tacoma front bumper
      • 16+ Tacoma Plate Bumpers
      • 16+ Tacoma Hybrid Front
      • 5th Gen 4Runner
      • 1st Gen Tundra Fronts
      • 1st Gen Sequoia Fronts
    • Rear Bumpers
      • 05-15 Tacoma Rears
      • 16+ Tacoma Rears
      • 5th Gen 4Runner Rears
      • 1st Gen Tundra Rears
      • 1st Gen Sequoia Rears
    • Rock Sliders
    • Accesories
  • Home
  • Front Bumpers
  • Rear Bumpers
  • Rock Sliders
  • Accesories

16 + tacoma rear bumpers


    16+ Tacoma Rear Bumpers

    HC Rear base Standard Features

     

    • Main Bumper CNC cut and formed from 3/16 HRPO Steel Plate 
    • 1/4'' Frame Plates
    • Built In Receiver Hitch (Not Rated but will handle anything that the factory hitch will) located behind the license plate ( Flip up license plate bracket not included but can be sourced very easy from amazon)
    • Cutouts for factory tow plug located next to the hitch
    • Fully Mig Welded
    • 1/2 thick recovery points for a 3/4 shackle w/ a 7/8 pin
    • Comes with  Light Cutouts  that fit Baja Design S2 Flush Mounts
    • Comes with cutouts for the factory backup sensors. NOTE: the factory blind spot monitoring system will not work with our bumpers.
    •  HC REAR comes with the bedside support brackets that support the bed after cutting, and all necessary hardware
    • HC REAR  comes with the bedside protection tubes
    •  HC REAR Bumper weighs around 140lbs. and 240lbs with swingouts
    • Comes raw steel and ready for the finish of your choice


    Pricing & Options

    • HC Rear Base bumper w/ standard features $915.00

            Add On's

    • Add Single swingout tire carrier. Comes with tire mount located on the passenger side and the universal mounting plate on the drivers side (on one swingout) for mounting accessories  such as the gas can holders, propane tank mounts, hi lift, etc.. Comes with the Southco , Timken Taper roller bearings, seal, Aluminum cap  and all necessary hardware. You can upgrade to the Brute Force Billet Latch. Swingout pivots off the passenger side of the rear bumpers and cannot be changed and locks open at 90 degrees.$ 495.00


    • Add Dual Swingout tire carrier. Comes with tire mount located on the passenger side and the universal mounting plate on the drivers side (on two separate shorter swingouts) for mounting accessories  such as the gas can holders, propane tank mounts, hi lift, etc.. Comes with the Southco latches , Timken Taper roller bearings, seals, Aluminum caps  and all necessary hardware. You can upgrade to the Brute Force Billet Latches. Swingouts pivots off the driver and passenger side of the rear bumper and locks open at 90 degrees.$ 925.00
    • Brute Force Billet Latch upgrade $125 ea. For more info or to order the latch by itself  please check out our accessory page
    • Add Fold down aluminum camp table ( only available for the single swingout) $150.00
    • Add Dual Gas Can Holder $135.00
    • Add Single Gas Can Holder $95.00
    • Hi Lift mount $95
    • Propane tank mount $105
    • Camera relocation bracket $25
    • If you've trimmed your factory flares to fit larger tires we can actually build your bumper with shorter sides to line up with the new fender opening. Just tell us how much you've cut off and we'll shorten the bumper that amount so everything lines up. $75.00 

            Installation 

    • Installation  HC REAR (no swingout) $265  HC REAR single swingout  $325  HC REAR Dual swingouts $385
    • NOTE: Installation includes the removal of the factory bumper, cutting the bedsides  and installing our bumper. we can install lights (supplied by customer) into the bumper at an additional cost but we don't do any wiring or electrical work. If you have an aftermarket bumper it would need to be removed before you come for the install or we can remove it at an additional cost.

          Powder Coating

    • Only available for local pickup or installation. We Don't Ship Anything Powder Coated.
    • HC Rear (no swingouts) $235 single swingout $320 Dual swingouts $370
    • Single Gas can holder $25 Dual Can Holder $35
    • Hi Lift mount $25
    • propane tank mount $20


    Shipping


    Shipping costs vary by location and carrier. Shipping has to be to a commercial address  with either a loading dock or forklift. We can also ship to a freight terminal which you would have to pick up from once it arrives to the terminal that's close to you.  Please use the contact form to ask us for a shipping quote. Please include your commercial address with a name of the business or a zip code so I can locate the closest freight terminal that's close to you. 

    Lead Times

     18-20 weeks .

    Order Process 50% deposit , Balance plus Shipping / Installation when complete. 

    Local pick up is available as well


    To place an order please fill out the contact form  and I will email you an invoice that will have a link to pay with a credit card or bank card. Make sure to list the options that you want, A zip code so that I can get a shipping quote, year and model of your vehicle

    Brute Force Fab

    Clovis, California, United States

    Copyright © 2021 Brute Force Fab - All Rights Reserved.

    Powered by GoDaddy

    This website uses cookies.

    We use cookies to analyze website traffic and optimize your website experience. By accepting our use of cookies, your data will be aggregated with all other user data.

    Accept