05-15 tacoma rear bumpers

---

• Main Bumper CNC cut and formed from 3/16 HRPO Steel Plate 
• 1/4'' Frame Plates
• Built In Receiver Hitch (Not Rated but will handle anything that the factory hitch will) located behind the license plate ( Flip up license plate bracket not included)
• Cutouts for factory tow plug located next to the hitch
• Fully Mig Welded
• 1/2 thick recovery points for a 3/4 shackle w/ a 7/8 pin
• Comes with  Light Cutouts for aftermarket back up lights . There are a ton of lighting options that fit. Baja Design squadron sports or pro's, rigid, Diode dynamics, ect.
•  HC REAR comes with the bedside support brackets that support the bed after cutting, and all necessary hardware.
• HC REAR  comes with the bedside protection tubes
•  HC REAR Bumper weighs around 140lbs and 240lbs with swingouts
• STD REAR Bumper weighs around 95lbs and 195lbs with swingouts
• Comes raw steel and ready for the finish of your choice

Pricing & Options

• HC Rear Base bumper w/ standard features $995.00
• STD Rear Base Bumper w/ standard Features  $875.00

        Add On's

• Add Single swingout tire carrier. Comes with tire mount located on the passenger side and the universal mounting plate on the drivers side (on one swingout) for mounting accessories  such as the gas can holders, propane tank mounts, hi lift, etc.. Comes with the  HD Brute Force latch, Timken Taper roller bearings, seal, Aluminum cap  and all necessary hardware. Swingout pivots off the passenger side of the rear bumpers and cannot be changed and locks open at 90 degrees.$ 645.00

• Add Dual Swingout tire carrier. Comes with tire mount located on the passenger side and the universal mounting plate on the drivers side (on two separate shorter swingouts) for mounting accessories  such as the gas can holders, propane tank mounts, hi lift, etc.. Comes with the Brute Force Latches, Timken Taper roller bearings, seals, Aluminum caps  and all necessary hardware. Swingouts pivots off the driver and passenger side of the rear bumper and locks open at 90 degrees.     $1175. 00
• Add Fold down aluminum camp table ( only available for the single swingout) $150.00
• Add Dual Gas Can Holder $135.00
• Add Single Gas Can Holder $95.00
• Propane tank mount $125.00
• Camera relocation bracket $25
• Stainless Steel Flip Up License Plate Bracket. $65.00
• If you've trimmed your factory flares to fit larger tires we can actually build your bumper with shorter sides to line up with the new fender opening. Just tell us how much you've cut off and we'll shorten the bumper that amount so everything lines up. $75.00 

        Installation 

• Installation   STD REAR (no swingout)$225  STD REAR w/ single swingout $295     STD REAR dual swingouts $325 HC REAR (no swingout) $285  HC REAR single swingout  $345 HC REAR Dual swingouts $395
• NOTE: Installation includes the removal of the factory bumper and installing our bumper. we can install lights (supplied by customer) into the bumper at an additional cost but we don't do any wiring or electrical work other than the winch. If you have an aftermarket bumper it would need to be removed before you come for the install or we can remove it at an additional cost.

      Powder Coating

• Only available for local pickup or installation. We Don't Ship Anything Powder Coated.
• STD Rear (no swingouts) $225 single swingout  $295.00  Dual swingouts $385
• HC Rear (no swingouts) $245 single swingout $335 Dual swingouts $395
• Single Gas can holder $25 Dual Can Holder $35
• propane tank mount $25

Shipping

Shipping costs vary by location and carrier. Shipping has to be to a commercial address  with either a loading dock or forklift. We can also ship to a freight terminal which you would have to pick up from once it arrives to the terminal that's close to you.  Please use the contact form to ask us for a shipping quote. Please include your commercial address with a name of the business or a zip code so I can locate the closest freight terminal that's close to you.